|
version 1.1.2.1, 2012/01/24 13:50:09
|
version 1.1.2.2, 2012/02/15 17:46:24
|
|
|
|
| |
// Copyright (c) 2005 DMTF. All rights reserved. |
| |
// <change cr="CIMCoreCR00735.001" type ="change">Update of |
| |
// descriptions based on Tech Edit review.</ |
| |
// <change cr="ArchCR00066.004" type="add">Add UmlPackagePath |
| |
// qualifier values to CIM Schema.</change> |
| |
// <change cr="ArchCR00089.003" type="add">Add PUnit qualifier values |
| |
// to Units qualifier values.</change> |
| |
// ================================================================== |
| |
// CIM_UninterruptiblePowerSupply |
| |
// ================================================================== |
| |
[Version ( "2.10.0" ), |
| |
UMLPackagePath ( "CIM::Device::CoolingAndPower" ), |
| |
Description ( |
| |
"Capabilities and management of an UninterruptiblePowerSupply. " |
| |
"The properties of the UPS Device indicate when incoming power " |
| |
"is trimmed or boosted, and the aggregated information of the " |
| |
"batteries, generators, and so on that comprise the Device. " |
| |
"These individual components (for example, multiple batteries) " |
| |
"can also be independently modeled and associated with the UPS." )] |
| |
class CIM_UninterruptiblePowerSupply : CIM_PowerSupply { |
| |
|
| |
[Override ( "Range1InputVoltageLow" ), |
| |
Description ( |
| |
"If the voltage (in millivolts) drops below the value " |
| |
"specified by Range1InputVoltageLow, the UPS will " |
| |
"compensate by boosting the voltage using its power " |
| |
"sources. A value of 0 indicates that the voltage at " |
| |
"which boosting occurs is \'unknown\'." ), |
| |
Units ( "MilliVolts" ), |
| |
PUnit ( "volt * 10^-3" )] |
| |
uint32 Range1InputVoltageLow; |
| |
|
| |
[Override ( "Range1InputVoltageHigh" ), |
| |
Description ( |
| |
"If the voltage (in millivolts) rises above the value " |
| |
"specified by Range1InputVoltageHigh, the UPS will " |
| |
"compensate by trimming the voltage. A value of 0 " |
| |
"indicates that the voltage at which trimming occurs is " |
| |
"\'unknown\'." ), |
| |
Units ( "MilliVolts" ), |
| |
PUnit ( "volt * 10^-3" )] |
| |
uint32 Range1InputVoltageHigh; |
| |
|
| |
[Override ( "Range2InputVoltageLow" ), |
| |
Description ( |
| |
"If the voltage (in millivolts) drops below the value " |
| |
"specified by Range2InputVoltageLow, the UPS will " |
| |
"compensate by boosting the voltage using its power " |
| |
"sources. A value of 0 indicates that the voltage at " |
| |
"which boosting occurs is \'unknown\'." ), |
| |
Units ( "MilliVolts" ), |
| |
PUnit ( "volt * 10^-3" )] |
| |
uint32 Range2InputVoltageLow; |
| |
|
| |
[Override ( "Range2InputVoltageHigh" ), |
| |
Description ( |
| |
"If the voltage (in millivolts) rises above the value " |
| |
"specified by Range2InputVoltageHigh, the UPS will " |
| |
"compensate by trimming the voltage. A value of 0 " |
| |
"indicates that the voltage at which trimming occurs is " |
| |
"\'unknown\'." ), |
| |
Units ( "MilliVolts" ), |
| |
PUnit ( "volt * 10^-3" )] |
| |
uint32 Range2InputVoltageHigh; |
| |
|
| |
[Description ( |
| |
"The indication of the capacity that remains in the UPS " |
| |
"batteries, generator, and so on. A value of \"Normal\" " |
| |
"(2) indicates that the remaining estimated minutes of " |
| |
"run-time are greater than the \'low power\' state " |
| |
"defined for the UPS (typically two minutes). A value of " |
| |
"\"Low\" (3) indicates that the remaining estimated " |
| |
"minutes of run-time are less than or equal to the " |
| |
"defined \'low power\' state of the device. A value of " |
| |
"\"Depleted\" (4) indicates that the UPS will be unable " |
| |
"to sustain the present load when and if the utility " |
| |
"power is lost (including the possibility that the " |
| |
"utility power is currently absent)." ), |
| |
ValueMap { "1", "2", "3", "4" }, |
| |
Values { "Unknown", "Normal", "Low", "Depleted" }, |
| |
MappingStrings { "MIF.DMTF|UPS Battery|001.1" }] |
| |
uint16 RemainingCapacityStatus; |
| |
|
| |
[Description ( |
| |
"TimeOnBackup indicates the elapsed time in seconds since " |
| |
"the UPS last switched to battery power, generator, or so " |
| |
"on or the time since the UPS was last restarted, " |
| |
"whichever is less. 0 is returned if the UPS is \'on " |
| |
"line\'." ), |
| |
Units ( "Seconds" ), |
| |
MappingStrings { "MIF.DMTF|UPS Battery|001.2" }, |
| |
PUnit ( "second" )] |
| |
uint32 TimeOnBackup; |
| |
|
| |
[Description ( |
| |
"EstimatedRunTime is an estimate in minutes of the time " |
| |
"that depletion of the battery, generator, or other " |
| |
"device, will occur under the present load conditions if " |
| |
"the utility power is off or is lost and remains off." ), |
| |
Units ( "Minutes" ), |
| |
MappingStrings { "MIF.DMTF|UPS Battery|001.3" }, |
| |
PUnit ( "minute" )] |
| |
uint32 EstimatedRunTime; |
| |
|
| |
[Description ( |
| |
"An estimate of the percentage of full charge remaining " |
| |
"for a UPS (that uses battery technology)." ), |
| |
Units ( "Percent" ), |
| |
Gauge, MappingStrings { "MIF.DMTF|UPS Battery|001.4" }, |
| |
PUnit ( "percent" )] |
| |
uint16 EstimatedChargeRemaining; |
| |
|
| |
|
| |
}; |
Return to
CIM_UninterruptiblePowerSupply.mof
CVS log
Up to [Pegasus] / pegasus / Schemas / CIM231 / DMTF / Device